How to caulk windows inside and out

Photo: rawpixel · CC0

To caulk windows, remove the old failing caulk, clean and dry the joint, then run a continuous bead where the window frame meets the exterior siding or trim and, inside, where the interior trim meets the wall. Use 100% silicone on glass, metal, vinyl and other non-porous joints you won't paint, and a paintable siliconized acrylic latex caulk on porous or painted surfaces. Never seal the weep holes at the bottom of the frame.

Which window joints to caulk (and which to leave alone)

Outside, caulk:

  • The joint between the window frame or exterior trim and the siding, brick or stucco (sides and top)
  • Gaps where trim pieces meet each other
  • Any cracked glazing seal at the glass on older windows, if the window maker allows it

Outside, don't caulk:

  • Weep holes or drainage slots along the bottom of the frame
  • The bottom edge of the window if the manufacturer's instructions say to leave it open for drainage
  • Moving parts, such as the sash of a sliding or hung window

Inside, caulk:

  • The joint between the interior casing and the wall
  • The joint between the stool (inside sill) and the wall or casing
  • Gaps between the frame and the casing where drafts get through

Choosing a sealant to caulk windows

JointGood fitWhy
Vinyl, aluminum or metal frame to vinyl or metal siding (exterior)100% siliconeBonds to non-porous materials, UV and weather resistant, ±25 % movement
Frame or trim to brick, stucco or concreteSiliconized acrylic latexMade for porous surfaces; low to medium movement
Glass to frame100% siliconeAdhesion to glass and aluminum
Interior casing to drywall or plaster, to be paintedSiliconized acrylic latexPaintable after curing, water cleanup, no odor
Interior sill in a spot with frequent condensation100% siliconeMold and mildew resistant

Senta 100% RTV Silicone sticks to glass, aluminum, metals, wood and most common non-porous building materials, is mold and mildew resistant, and stays flexible from extreme cold to extreme heat. It is not paintable, and it isn't recommended on concrete, natural stone or other porous surfaces.

Senta Siliconized Acrylic Latex Caulk is designed for gaps around windows, walls and doors on porous surfaces like brick, concrete, wood and plaster. It's paintable, weatherproof once cured, and cleans up with water. It isn't meant for joints permanently exposed to water.

Not sure which way to go? Our comparison of silicone vs. acrylic caulk goes deeper.

Tools and materials

  • Utility knife, caulk removal tool and plastic scraper
  • Stiff brush, clean rags and isopropyl alcohol
  • Backer rod (for gaps deeper than about 1/2 in)
  • Painter's tape
  • Caulking gun
  • 100% silicone and/or siliconized acrylic latex caulk
  • Gloves and safety glasses
  • Ladder, used safely, for upper floors

How to caulk windows outside

  1. Pick the day. Work between 40 °F and 105 °F on a dry day. With acrylic caulk, the joint must stay dry for at least 2 hours, so skip it if rain or frost is expected.
  2. Strip the old caulk. Cut along both edges and pull it out. Scrape off what's left. New sealant over old, cracked caulk won't last. See how to remove old silicone caulk.
  3. Clean and dry. Brush out dirt and cobwebs. Wipe non-porous surfaces with isopropyl alcohol and let them dry.
  4. Fill deep gaps. Push in backer rod so the sealant depth ends up about half the joint width.
  5. Tape if you want crisp lines. Run painter's tape along both sides of the joint.
  6. Apply. Cut the nozzle to match the gap, hold the gun at about 45 degrees and push a steady, continuous bead into the joint.
  7. Tool and untape. Smooth the bead within a few minutes (within 5 minutes for Senta silicone), then pull the tape while the sealant is still wet.
  8. Let it cure. Senta silicone cures at about 1/8 in of bead depth per 24 hours. Keep sprinklers and pressure washers away until it has cured.

How to caulk windows inside

Inside, the goal is usually a clean, paintable seal that stops drafts.

  1. Remove loose or cracked caulk and dust off the joint.
  2. For bare drywall or plaster that's very porous, the Senta acrylic data sheet suggests priming with the caulk diluted 1 part to 4–5 parts water.
  3. Run a thin bead of siliconized acrylic latex where the casing meets the wall and where the stool meets the casing.
  4. Smooth with a damp finger or tool and wipe excess with a damp rag.
  5. Paint once it has cured, following the data sheet.

On interior sills where condensation sits regularly, consider silicone in a matching color instead, since it won't be painted anyway.

Common mistakes

  • Caulking the weep holes. Water then gets trapped in the frame.
  • Caulking over dirt or old caulk. Adhesion fails within a season.
  • Huge, shallow smears. A bead that's too thin or too wide tears when the joint moves.
  • Silicone on brick or stucco. Senta silicone isn't recommended on porous masonry; use the acrylic caulk there.

FAQ

Should I caulk windows from the inside or the outside?

Both. The exterior seal keeps water out; the interior seal stops drafts and gives a clean, paintable finish.

Can I use silicone around a window I plan to paint?

Not on the parts you'll paint. 100% silicone isn't paintable, so use siliconized acrylic latex on painted trim and silicone only where the joint stays unpainted.

Should I caulk the bottom of the exterior window frame?

Leave weep holes and drainage paths open, and follow the window manufacturer's instructions for the bottom edge.

For window frames and glass, start with Senta 100% RTV Silicone.